EKF CompactPCI CPU Boards: CCD-CALYPSO • 3U General Purpose

CCD-CALYPSO

3U, General Purpose CompactPCI® CPU Board

Description

CCD Product Information
CCD User Guide
CCA Side Board
CCB Side Board
CCE Side Board
C23 Side Board
CCT Rear I/O Module

BIOS Update
Graphics Drivers
Embedded Graphics Drivers
Ethernet Drivers
Chipset Software
Audio Drivers
SATA Drivers
MBM Monitor
MBM INI File

E-Mail on BIOS Update
E-Mail bei BIOS Update

Photos
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11
Print Quality 300dpi 10x15cm .JPG ©EKF

CCD-CALYPSO

General Purpose CompactPCI® CPU

Scalable from 1GHz Ultra Low Voltage Celeron® M to 2.0GHz Pentium® M
Dual-Screen Video • Dual Gigabit Ethernet • Dual Channel Memory • Triple SATA

Scalable from the ULV Celeron® M processor up to the 2.0GHz Pentium® M, and provided with 2GB dual channel capable DDR2 RAM, the CCD-CALYPSO is a versatile 4HP/3U (single size Eurocard) CompactPCI® CPU board, designed especially for systems which require reasonable performance at low power consumption.

The chipset is based on PCI Express technology and has a powerful dual-screen integrated graphics accelerator. The DVI-I video interface allows for simultaneous attachment of both, advanced (digital) and legacy (analog) flat panel displays and CRT monitors (D-SUB connector optionally).

CCD-CALYPSO - Rugged General Purpose CPU Board

CCD-CALYPSO - General Purpose CompactPCI® CPU Board

The CCD-CALYPSO is equipped with two independent PCIe Gigabit Ethernet controllers for high speed communication. Seven USB 2.0 ports are provided for attachment of peripheral devices. In addition, a CompactFlash mezzanine module (C10-CFA) can accommodate an industrial grade CF card. As an alternate, the 1.8-inch HDD/SSD carrier module C30-PATA is available as on-board mass-storage device (option).

A set of local expansion interface connectors may be used to directly attach a mezzanine companion card (aka side board) for I/O, audio- and legacy support, which can carry in addition a 2.5-inch IDE hard disk drive.

As an option, a rear I/O transition module is available to the CCD-CALYPSO, which e.g. provides the Serial ATA connectors (2 x SATA, 1 x eSATA).

CCD-CALYPSO with CCE-PUNK Mezzanine Module

CCD-CALYPSO with CCE-PUNK Mezzanine Option (1394 FireWire)

Benefits of the CCD-CALYPSO

Pentium® M 2GHz (FSB 533MHz) CompactPCI CPU
2 x 1GB DDR2 Memory (Dual Channel Mode Capable)
Dual-Screen Graphics Controller
Dual Gigabit Ethernet Controllers
Triple SATA I/F
Seven USB 2.0 channels
On-Board CompactFlash or on-Board 1.8-Inch Hard Disk
PCI Express Chipset i915GM Alviso
Mezzanine Expansion Board and Rear I/O Transition Module Options
RoHS compliant

CCD-CALYPSO with CCT-RIO

CCD-CALYPSO w. CCB-BOSSANOVA & 2.5-Inch Hard Disk & C15-DON USB Flash Drive Module

Feature Summary CCD-CALYPSO
Form Factor	CompactPCI Single size CompactPCI style Eurocard (160x100mm²), front panel width 4HP (20.3mm)
Processor	Designed for Intel® Pentium® M Micro FC-BGA 479 processors (90nm Dothan), maximum junction temperature 100°C CCD-2: 1.0GHz ULV Celeron® M (Dothan 373), 400MHz FSB, 512KB L2 cache, 5W CCD-3: 1.4GHz LV Pentium® M (Dothan 738), 400MHz FSB, 2MB L2 cache, 10W CCD-6: 2.0GHz Pentium® M (Dothan 760), 533MHz FSB, 2MB L2 cache, 27W
Chipset	Intel® i915GM (Alviso) chipset consisting of: 82915GM Graphics/Memory Controller Hub (GMCH) with Intel® Graphics Media Accelerator (GMA) 900 82801FB I/O Controller Hub (ICH6) 82802 Firmware Hub (FWH)
Memory	Dual 200-pin SO-DIMM socket, DDR2 533 SDRAM, 2 x 1GB maximum, symmetric dual channel capable
Video I/O	Analog monitor and digital flat-panel display support by DVI-I connector (front panel), up to 2048x1536 pixel 16M colours @75Hz refresh rate (analog), up to 1600 x 1200 pixel 16M colours @60Hz (digital), incorporates PanelLink Digital technology (Silicon Image). Front panel option: D-Sub (female HD15) VGA connector available, replaces DVI-I connector Rear I/O option: Analog video across J2/P2 (CCT-RIO rear I/O transition module) Dual screen capable 2 x 1600 x 1200 pixel (one display attached to the front panel, the other to the back panel, or both to the front panel by means of a DVI-I splitter cable)
USB I/O	All ports over-current protected, data transfer rate of up to 480Mbps, conforming to USB2.0: 2 x USB type A connector (front panel) 3 x USB J2/P2 Rear I/O option (CCT-RIO rear I/O transition module) 2 x USB expansion interface option (CCA-LAMBADA / CCB-BOSSANOVA / CCE-PUNK mezzanine companion board) USB Flash drive module C15-DON option (USB stick on-board)
Ethernet I/O	Dual 10/100/1000Mbps Gigabit Ethernet controller Accessible via RJ45 jacks from the front panel Option 1 x GbE across J2/P2 with attached CCT-RIO rear I/O transition module Jumbo Frame support up to 9KB
Mezzanine I/O	On-board LPC/USB/AC97 Super-I/O, USB and audio interface connector ATA/IDE expansion connector High Speed PCI Express expansion connector Suitable mezzanine companion boards available: CCA-LAMBADA: Front panel COM, USB, AC'97 audio, PS/2 keyboard/mouse, on board hard disk drive 1.8-inch or 2.5-inch CCB-BOSSANOVA: Front panel up to 2 x COM, up to 2 x USB, PS/2 keyboard/mouse, on board hard disk drive 1.8-inch or 2.5-inch CCE-PUNK: Front panel 2 x COM, 2 x USB, 2 x 1394a FireWire, on board hard disk drive 1.8-inch or 2.5-inch C10-CFA CompactFlash adapter module C15-DON on-board USB stick module (USB Flash disk) C23-SATA PCIe to SATA controller, USB SSD, COM ports C30-PATA 1.8-inch HDD/SSD
PATA (IDE)	Ultra ATA/100 connector, handover to CCA-LAMBADA / CCB-BOSSANOVA / CCE-PUNK mezzanine expansion board with optional on-board 2.5-inch hard disk drive or external device CompactFlash socket C10-CFA supplied for a CF memory card Option 1.8-inch on-board HDD/SSD module C30-PATA, replaces CompactFlash facility
SATA (Serial ATA)	Triple-channel Serial ATA I/F available for J2/P2 rear I/O option, suitable rear I/O transition module CCT-RIO (2 x system-internal SATA, 1 x eSATA for attachment of external devices)
CompactPCI	ICH6 integrated 32-bit PCI bridge, 133MBps CPCI master
PCI Express	1-Lane PCIe connector (option) for future mezzanine companion board
J2/P2 Rear I/O	3 x Serial ATA (SATA), 2 x system internal SATA connectors, 1 x external eSATA connector GB Ethernet (switched by BIOS between front panel I/O and rear I/O) 3 x USB VGA Analog Video (Option), or GPIO Keyboard, Mouse COM1 (TTL Level) Suitable rear I/O transition modules CCT-RIO available
BIOS	Phoenix BIOS with EKF enhancements 8Mbit Flash memory Updates available from website ekf.com
Drivers	Intel graphics drivers Intel networking drivers
Typical Power Requirements	Board	+3.3V +0.17V/-0.1V		+5V +0.25V/-0.15V
		MaxPower LFM/HFM ¹	WinXP Idle LFM/HFM¹	MaxPower LFM/HFM ¹	WinXP Idle LFM/HFM ¹
	CCD-2-CALYPSO	2.7A ²	2.2A ²	1.2A ²	0.5A ²
	CCD-3-CALYPSO	2.9A/2.9A	2.2A/2.2A	1.2A/2.4A	0.7A/0.9A
	CCD-6-CALYPSO	3.0A/3.3A	2.3A/2.3A	1.2A/5.2A	0.7A/1.6A
Thermal Conditions Environmental Conditions	Operating temperature: 0°C ... +60°C Storage temperature: -40°C ... +85°C, max. gradient 5°C/min Humidity 5% ... 95% non condensing Altitude -300m ... +3000m Shock 15g 0.33ms, 6g 6ms Vibration 1g 5-2000Hz
EC Regulations	EN55022, EN55024, EN60950-1 (UL60950-1/IEC60950-1) 2002/95/EC (RoHS)
MTBF	tbd
Typical Performance Rating Measured with PCMark2002 under Windows XP, 1GB DDR2 533	Board	Processor		CPU/MEM Score
	CCD-2-CALYPSO	1.0GHz ULV Celeron® M (Dothan 373)		4735/8642
	CCD-3-CALYPSO	1.4GHz LV Pentium® M (Dothan 738)		tbd
	CCD-6-CALYPSO	2.0GHz Pentium® M (Dothan 760)		tbd

¹Intel SpeedStep® Frequency Modes. LFM: Low Frequency Mode, HFM: High Frequency Mode
²The ULV Celeron® M processor on CCD-2 does not support Intel SpeedStep® (always High Frequency Mode)

subject to change

CCD-CALYPSO w. C30-PATA 1.8-Inch Hard Disk Module (Picture Similar)

CCD-CALYPSO Block Diagram

CCD-CALYPSO Component Assembly (Top View)

Available as a rear I/O expansion board to the CCD-CALYPSO CPU card, the CCT-RIO is provided with several I/O port connectors, to be used either in addition to the CCD front panel connectors or alternatively. Being mainly a passive rear I/O transition module, groups of signals from the CCD-CALYPSO CPU board are passed across the CompactPCI J2/P2 connector to the CCT-RIO. Some of the signals are available locally on the CCT board for system internal wiring only, while other connectors such as VGA-Video and Gigabit Ethernet are mounted into the back panel for external use. USB and SATA (eSATA) channels are provided both on-board and externally.

Typically the CCT-RIO ist equipped with a 4-HP rear panel (20.3mm width). As a custom specific option, an 8-HP panel is available with additional connectors.

Utilization of the CCT-RIO transition module adds a level of I/O functionality that is not available with the CCD-CALYPSO CPU board alone. Further on, swapping the CPU card is simplified by means of rear I/O, which is important for efficient system maintenance (MTTR).

CCT-RIO

CCT-RIO Block Diagram

CCT-RIO Component Assembly (Top View)

Ordering Information
Alias	Ordering No.	Short Description
CALYPSO	CCD-2(R)-CALYPSO	3U/4HP CPCI CPU board, 1.0GHz ULV Celeron® M (Dothan 373), 1GB (2 x 512MB) DDR2 SDRAM, CompactFlash Adapter (C10-CFA)
CALYPSO	CCD-3(R)-CALYPSO	Similar to CCD-2-CALYPSO, 1.4GHz LV Pentium® M (Dothan 738)
CALYPSO	CCD-6(R)-CALYPSO	Similar to CCD-2-CALYPSO, 2.0GHz Pentium® M (Dothan 760)
LAMBADA	CCA-1-LAMBADA	3U CompactPCI Super-I/O module, local mezzanine expansion board complementing the CCD-CALYPSO, front panel width 4HP, with keyboard/mouse, RS-232, optional audio connectors & AC'97 Codec, mounting on top or bottom of the CCD-CALYPSO
BOSSANOVA	CCB-1-BOSSANOVA	3U Super-I/O module, local mezzanine expansion board complementing the CCD-CALYPSO, front panel width 4HP, 2 x USB, 1 x RS-232, PS/2 MS/KB, mounting on top or bottom of the CCD-CALYPSO
BOSSANOVA	CCB-2-BOSSANOVA	3U Super-I/O module, local mezzanine expansion board complementing the CCD-CALYPSO, front panel width 4HP, 2 x RS-232, PS/2 MS/KB, mounting on top or bottom of the CCD-CALYPSO
PUNK	CCE-1-PUNK	3U Super-I/O module, local mezzanine expansion board complementing the CCD-CALYPSO, front panel width 4HP, 2 x RS-232, 2 x USB, 2 x 1394a FireWire 400Mbps, mounting on top of the CCD-CALYPSO
SATA	C23-SATA	3U Super-I/O module, local mezzanine expansion side board complementing the CCD-CALYPSO, front panel width 4HP, PCIe to SATA/PATA controller, 2 x RS-232, 1 x RS-232/RS-485, USB SSD, option audio codec AC'97, option TPM module, mounting on top of the CCD-CALYPSO
RIO	CCT-1-RIO	Rear I/O transition module for CCD-CALYPSO with SATA connectors

CCD-*-CALYPSO: suitable for 64-bit CPCI J2/P2 backplane
CCD-*R-CALYPSO: suitable for rear I/O across J2

C10-CFA CompactFlash Adapter for CCD-CALYPSO (Included with CCD-CALYPSO, w/o CF-Card)

Option C30-PATA 1.8-Inch Hard Disk or Solid State Drive (SSD) Module

EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 Hamm • Germany
Phone +49 (0)2381/6890-0 • Fax +49 (0)2381/6890-90 • E-Mail